Question 1

What is the quantification range?

Accepted Answer

The target mass range is 0.2–100 ng in the assay. The stated initial concentration range is 0.01–100 ng/µL (10 pg/µL at the lower end), depending on sample input. Initial sample concentration is measured before dilution; target mass equals initial concentration multiplied by the sample volume. These are different quantities.

Question 2

How do I prepare the working solution?

Accepted Answer

Use the supplied 1X working solution directly; no reagent dilution is required.

Question 3

Can I use this kit with Qubit fluorometers?

Accepted Answer

The supplier protocol supports use with the matching Qubit assay program. Use this kit's own standards, the specified sample volume and the correct consumables for the Qubit model. Compatibility does not imply Thermo Fisher endorsement or identical performance. For the 1X assay on older Qubit models, verify that the appropriate assay program is installed.

Question 4

Which Biofargo fluorometers support this assay?

Accepted Answer

X1 and X3 list the corresponding dsDNA or ssDNA program. The eight-position X3 uses different tubes from the single-sample X1.

Question 5

How much sample is required?

Accepted Answer

Add 1–20 µL of sample and adjust the working solution to a final volume of 200 µL. Choose the input volume so the target mass lies within the assay range. Dilute samples that exceed the upper limit.

Question 6

Which assay tubes should I use?

Accepted Answer

Use clear, thin-wall 0.5 mL assay tubes for Biofargo X1 and Qubit 2/3/4. Use the instrument-specified clear 0.2 mL tubes or eight-tube strips for Biofargo X3; Qubit Flex requires its specified 0.2 mL assay tube strips. Keep the total assay volume at 200 µL.

Question 7

How long does the assay take?

Accepted Answer

Incubate for 2 minutes at 20–25 °C, protected from light, after mixing. This is the incubation time, not the total preparation and measurement time. The signal remains stable for up to 3 hours when protected from light.

Question 8

Do I need new standards?

Accepted Answer

Use the two standards supplied with this kit and the matching assay program. A new calibration for each run is recommended. Do not reuse a calibration generated with a different kit. For a plate reader, prepare a dilution series and fit a standard curve.

Question 9

Does the reaction count equal the number of unknown samples?

Accepted Answer

The listed count is the nominal assay format. Standards, controls, repeat measurements and handling losses reduce the number of unknown samples that can be measured.

Question 10

How should I store the kit?

Accepted Answer

Ship on ice. Store all components at 2–8 °C, protected from light.

Question 11

Is this product intended for diagnostic use?

Accepted Answer

No. For research use only. Not for diagnostic or therapeutic procedures.

Parameter	Specification
Biofargo catalog numbers	BF-T1005-S / BF-T1005
Target	double-stranded DNA (dsDNA)
Total target amount per assay	0.2–100 ng
Initial sample concentration	0.01–100 ng/µL (10 pg/µL at the lower end), depending on sample input
Sample input	1–20 µL
Final assay volume	200 µL per tube or well
Working-solution preparation	Use the supplied 1X working solution directly; no reagent dilution is required.
Incubation	2 minutes at 20–25 °C, protected from light
Signal stability	Up to 3 hours, protected from light
Instrument formats	Biofargo X1 and X3; Qubit fluorometers with the matching assay; fluorescence microplate readers
Plate-reader settings	485 nm excitation / 530 nm emission
Available formats	BF-T1005-S: 100 reactions; BF-T1005: 1,200 reactions
Intended use	Research use only

Component	Designation	BF-T1005-S (100 reactions)	BF-T1005 (1,200 reactions)	Function
1X dsDNA HS Working Solution	1X	20 mL	250 mL	Ready-to-use detection solution
dsDNA HS Standard QS0	QS0	100 µL	5 mL	Blank standard; 0 ng/µL
dsDNA HS Standard QS1	QS1	100 µL	5 mL	High standard; 10 ng/µL

Description

Specifications

Features

Applications

Kit Components

Storage & Shipping

Frequently Asked Questions (FAQs)

Compatible Instruments

Documents

Biofargo 1X dsDNA HS Assay Kit